Sanding Cutting Board – UPDATED 2020 – How To Refinish A Cutting Board?

You want your favorite cutting board to last the entire life. However, with time, the surface of the board starts showing deep cut marks from cutting with a knife. Food particles can get into these crevices and produce stains.

Instead of investing in a new board, you can refinish your cutting board with periodical sanding. In this guide, we discuss how you can care for your cutting board with sanding. We also take a look at the right procedure you should follow for sanding your wood and plastic cutting boards to keep them new-like forever.

Sanding Cutting Board – A Complete Guide

You can sand a cutting board with the help of a sandpaper. You can sand the cutting board by starting with a rougher sandpaper and then moving with a finer one. depending on how bad your board has become, you can use 2-4 different grit levels to smoothen the surface.

If your cutting board has intensive knife marks, you can start with 50 grit sandpaper which is quite coarse. You can take 80 grit if the knife marks are not so bad. Once you remove the knife marks and stains, you can take a finer sandpaper 100-120 grit and start sanding until you feel the board smooth.

You can continue sanding with a finer sandpaper till you get the surface smooth to your liking. Then, wipe it off with a cloth and oil the board using food grade oil or beeswax. Leave the board for a few hours before using it again. You have your refinished cutting board ready for use.

Sanding A Plastic Cutting Board – What You Should Know?

Plastic cutting boards are likely to wear with use and eventually get a ragged look from foods and cut marks. However, it is possible to refresh the cutting board and make it as good as new, saving the time and money of getting a new one.

You can sand a plastic cutting board using a sander, sandpaper and scraper. You can start by covering the work area using a newspaper or cloth to catch the waste. Secure the board to the surface using clamps. Then, you can prepare the board for sanding by scraping the surface with the use of a metal scrubber or scraper. You basically remove any surface plastic and clean it.

Now, you can start sanding the plastic cutting board using the coarse part of the sandpaper. It is recommended that you start with a low grit sandpaper and an orbital sander to remove all the stains and cut marks on the surface. Clean the board and dry before switching to a high grit to smoothen the surface so that it avoids getting new stains.

Then, you can clean the board by first rinsing with water to remove dust and particles and then with soap. You can use a sponge and dish soap again to clean the board finally before drying it and enjoying the new-like cutting board.

How To Refinish A Cutting Board?

If you care properly for your wood cutting board, it can keep working great for decades. If your board has become rough and stained, you can easily restore it to its original charm in just a few steps. Here are the essential steps to refinish your wood cutting board.

You can start by preparing a natural butter which will bring shine to your wood cutting board. Melt some beeswax and add four times coconut oil to it. Mix the two ingredients till they combine well. Allow the mixture to cool and solidify.

Clean the cutting board using a cloth and vinegar. You can soak the board in vinegar for some time if it is too stained. Then, rinse it with warm water and dry. To disinfect further, sprinkle sea salt and scrub it on the board with a lemon. Leave it on for some time before rinsing and drying.

The next step is sanding the board using a sandpaper along the grain to smoothen out the dents and cuts. You can start with 80-grit before proceeding with 120-grit and 220-grit. Wipe with a cloth and you will feel it smooth and lighter in color.

Once sanding is done, you can use a clean cloth to apply the prepared wood butter until it is well-oiled covering all the edges and the back. Let the butter sit for some hours before wiping it off. Now your cutting board should look refurbished and in new-like condition. You can maintain it by scrubbing with hot soapy water after each use and drying it. Use the wood butter to condition the board once in a month.

Can I Sand My Cutting Board?

A lot of homeowners are not sure whether they should sand their cutting boards. Most people replace their cutting boards for new ones when they get stained and rough from knife marks and regular cutting. However, you should know that sanding the cutting board is a great way to refinish it and make it looking and working like a new one, saving you money.

You can sand the cutting board easily using a planer or an orbit sander. You can also sand the cutting board using a 80 grit sandpaper until you get desired smoothness. Then, you can move to 100, 180, 400 grits to remove the marks from the previous sanding to make the board smoother. Once sanded, you can oil your cutting board and it should look like new.

Plastic Cutting Board Smells? Here’s What You Should Do

While plastic cutting boards are quite easy to care for and convenient to use, they can often get bacteria accumulated in the knife-marks. A lot of people complain about their plastic cutting boards smelling bad. Here are some of the easiest ways to deal with this problem.

You can use a mixture of bleach and water and use it with a sponge to clean your cutting board. Bleach would kill the bacteria and remove the smell. However, if you don’t want to use this chemical, you can make a paste of baking soda, salt and water. Cleaning the board with this solution eliminates stains and bacteria from the surface and grooves.

To disinfect your plastic cutting board, you can try soaking it in a white vinegar solution or spray 3% hydrogen peroxide solution. After a few minutes, you can wash it with soap and water. Use a scrub whenever you clean the board so that you can remove bacteria and food particles from the crevices and knife grooves.

Leave a Comment